Cisco 300-410 Dumps - 100% Cover Real Exam Questions (Updated 594 Questions)
Real 300-410 dumps - Real Cisco dumps PDF
Cisco 300-410 exam is a certification test designed for network professionals seeking to enhance their skills and demonstrate their expertise in implementing advanced routing and services. It covers a range of advanced topics and requires a thorough understanding of the subject matter. By passing 300-410 exam, candidates can advance their careers and demonstrate their commitment to the field.
NEW QUESTION # 166
Refer to the exhibit.
The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host
192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action resolves the issue without opening full access to this router?
- A. Run the show access-list FILTER command to view if the SSH entry has any hit statistic associated with it
- B. Move the SSH entry to the beginning of the ACL
- C. Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow works
- D. Temporarily remove the ACL from the interface to see if the flow works
Answer: B
NEW QUESTION # 167
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.1.2.0/24
- B. 10.2.3.0/26
- C. 10.1.4.0/26
- D. 10.2.2.0/24
Answer: D
NEW QUESTION # 168
Refer to the exhibit.
A client is concerned that passwords are visible when running this show archive log config all.
Which router configuration is needed to resolve this issue?
- A. MASS-RTR(config-archive-log-cfg)#password encryption aes
- B. MASS-RTR(config)#service password-encryption
- C. MASS-RTR(config-archive-log-cfg)#hidekeys
- D. MASS-RTR(config)#aaa authentication arap
Answer: C
Explanation:
NEW QUESTION # 169
Drag and drop the descriptions from the left onto the corresponding MPLS components on the right.
Answer:
Explanation:
NEW QUESTION # 170
Refer to the exhibit.
An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed?
- A. Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2.
- B. Modify prefix-list ccnp3 to add 10.1.64.0/20 le 24
- C. Modify route-map ospf-to-eigrp permit 10 and match prefix-list ccnp2.
- D. Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32
Answer: C
NEW QUESTION # 171
Refer to the exhibit. An engineer cannot determine the time of the problem on R1 due to a mismatch between the router local clock and legs. Which command synchronizes the time between new log entries and the local clock on R1?
- A. service timestamps log datetime msec show-timezone
- B. service timestamps datebug datetime localtime msec
- C. service timestamps debug datetime msec show-timezone
- D. service timestamps log datetime locatetime msec
Answer: D
NEW QUESTION # 172
Refer to the exhibit.
Refer to the exhibit. The services at branch B are down. An engineer notices mal rouler A and router B are not exchanging any routes Which configuration resolves the issue on router B?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 173
Drag and drop the actions from the left into the correct order on the right to configure a policy to avoid following packet forwarding based on the normal routing path.
Answer:
Explanation:
NEW QUESTION # 174
Refer to the exhibit.
An engineer cannot copy the IOS.bin file from the FTP server to the switch.
Which action resolves the issue?
- A. Use the copy flash:/ ftp://[email protected]/IOS.bin command.
- B. Add the IOS.bin file, which does not exist on FTP server.
- C. Make memory space on the switch flash or USB drive to download the file.
- D. Allow file permissions to download the file from the FTP server.
Answer: B
NEW QUESTION # 175
Refer to the exhibit.
BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?
(Choose two)
- A. Configure a three-color policer instead of two-color policer under class COPP-CRITICAL-
7600 - B. Configure IP CEF to CoPP policy and BGP to work
- C. Configure a higher value for CIR under the class COPP-CRITICAL-7600
- D. Configure a higher value for CIR under the default class to allow more packets during peak traffic
- E. Configure BGP in the COPP-CRITICAL-7600 ACL
Answer: D,E
Explanation:
The policy-map COPP-7600 only rate-limit HTTP & HTTPS traffic (based on the ACL conditions) so any BGP packets will be processed in the class "class-default", which drops exceeded BGP packets. Therefore we have two ways to solve this problem:
+ Add BGP to the ACL with the statement "permit tcp any any eq bgp"
+ Configure higher value for CIR in default class as 2Mbps is too low for web traffic (http &
https)
NEW QUESTION # 176 
Refer to the exhibit. Which action resolves intermittent connectivity observed with the SNMP trap rackets?
- A. Add one new entry in the ACL 120 to permit the UDP port 161.
- B. Increase the CIR of the mgmt class map.
- C. Decrease the committed burst size of the mgmt class map.
- D. Add a new class map to match TCP traffic.
Answer: B
Explanation:
Section: Mixed Questions
NEW QUESTION # 177
Refer to the exhibit.
R1 and R2 are configured for EIGRP peering using authentication and the neighbors failed to come up. Which action resolves the issue?
- A. Configure a matching key-id number on both routers
- B. Configure a matching key-chain name on both routers
- C. Configure a matching lowest key-id on both routers
- D. Configure a matching authentication type on both router
Answer: A
NEW QUESTION # 178 
Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot. Which action resolves the issue?
- A. Configure IPv6 on the routers B and C interfaces
- B. Configure the Spoke 2 users IP on the router B OSPF domain
- C. Configure encapsulation dot1q 78 on the router C interface.
- D. Configure OSPFv2 on the routers B and C interfaces
Answer: A
NEW QUESTION # 179 
Refer to the exhibit A company builds WAN infrastructure between the head office and POPs using DMVPN hub-and-spoke topology to provide end-to-end communication All POPs must maintain point-to-point connectivity with the head office Which configuration meets the requirement at routers R12 and R13?
- A. Option B
- B. Option D
- C. Option C
- D. Option A
Answer: B
NEW QUESTION # 180
Refer to the exhibit.
A company is evaluating multiple network management system tools. Trending graphs generated by SNMP data are returned by the NMS and appear to have multiple gaps. While troubleshooting the issue, an engineer noticed the relevant output. What solves the gaps in the graphs?
- A. Remove the class map NMS from being part of control plane policing.
- B. Remove the exceed-rate command in the class map.
- C. Separate the NMS class map in multiple class maps based on the specific protocols with appropriate CoPP actions
- D. Configure the CIR rate to a lower value that accommodates all the NMS tools
Answer: C
Explanation:
Reference:
https://tools.cisco.com/security/center/resources/copp_best_practices
The class-map NMS in the exhibit did not classify traffic into specific protocols so many packets were dropped. We should create some class-map to classify the receiving traffic. It is also a recommendation of CoPP/CPP policy:
"Developing a CPP policy starts with the classification of the control plane traffic. To that end, the control plane traffic needs to be first identified and separated into different class maps."
NEW QUESTION # 181
Exhibit:
An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP peers. Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?
- A. R4 and R5
- B. R1 and R5
- C. R1 and R4
- D. R2 and R5
Answer: A
Explanation:
Explanation
When R2 & R5 are route reflectors (RRs), routes from R4 & R8 are advertised to R5 and R5 advertises to R2. But R2 would drop them as R2 is also a RR. Therefore some routes are missing on R1 to advertise to eBGP peers.
Good reference:
https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2015/pdf/TECRST-2310.pdf Route reflectors (RR) must be fully iBGP meshed so we cannot configure RR on both R1 and R5.
We should choose routers at the center of the topology RRs, in this case R4 & R5.
NEW QUESTION # 182
......
Realistic PassReview 300-410 Dumps PDF - 100% Passing Guarantee: https://vcetorrent.passreview.com/300-410-exam-questions.html